fc1001_manual
email(1)

banner-fc1001

Introduction

The Aceco FC1001 hand-held frequency counter is a supurb value low cost instrument. It is compact, truly pocket sized, test instrument designed for ease of use and dependable performance. Supplied as a complete with internal NiCd pack, AC wall charger and 7 section telescopic antenna.

Specifications

Frequency range

10 MHz - 3 GHz

Weight

210 g

Size

80 mm high x 68 mm wide x 31 mm deep

Impedance

50 Ohms (BNC Socket)

Case

Stamped aluminum with black anodized finish

Battery

Internal 4 x AA 600 mAH NiCd pack

Power

9 VDC 300 mA

Timebase

Less than 1 PPM at room temperature

Features

  • 8 digit Liquid Crystal Display
  • Low power consumption (Average 6 hour battery life)
  • Supplied with NiCd pack, AC wall charger and telescopic antenna
  • Hold switch to lock display
  • High speed counter with 100 Hz resolution

Controls

  1. Power Switch - This slide switch turns the counter on and initiates a 2 second test of all the LCD segments.
  2. Hold Button - This holds the current display and stops the counter from counting.
  3. Calibration - The calibration adjustment opening is located on the front panel of the counter. This allows access to the trimmer capacitor that provides about a 10 PPM adjustment range of the time base oscillator.This is not usually necessary but to do so read a signal of an known frequency before adjusting the trimmer for correct frequency display. If you calibrate at 4.1943 MHz or above then the counter will be more accurate.

Warranty

Aceco Electronics, Corp. guarantees the counter and accessories for one year against defects in manufacture. This warranty does not cover items that have been modified, subject to unauthorized repairs, misuse or abuse. This warranty does not cover damage caused by excessive power levels applied to the signal input. Never make any kind of connection between the counter and a transmitter.

Hints And Tips

  1. NiCd Operation

    This frequency counter can operate for up to six hours from its fully charged NiCd batteries. They are charged when the unit is plugged into the supplied AC/DC adapter. Full recharge will occur over 12 to 16 hours. Before recharging the batteries you should be deep cycled occasionally by allowing them to completely discharge to maintain maximum battery capacity. The NiCd batteries should last for several years. However, it is a good idea to check them every twelve months for signs of corrosion or leakage. Always replace the whole set if any one cell fails
     
  2. Signal Input

    When using the counter with an antenna for signal pick up, random frequencies may appear on the display. This is quite normal and is caused by the high gain of the receiver circuits which amplify noise in the absence of a strong readable signal. Never get the unit too close to a transmitter as internal damage will result.
     
  3. Antenna Selection

    The supplied telescopic antenna is best for general purpose use. This is because its length can be adjusted to suit the frequency required. Usually you will want a shorter antenna for UHF and a fully extended one for VHF / HF.
  4. Reception Distance From Transmitter

    The distance from which you will be able to receive frequencies will depend upon the type and location of the transmitting antenna, transmitter output power and the frequency in use.
    Some typical distances are:
     

Cordless Phone

0.3 meters

Cellular Phone

3 - 20 m

CB radio

2 - 8 m

VHF Two Way Radio

3 - 30 m

UHF Two Way Radio

3 - 30 m


Input Sensitivity ( Typical )

Amplifier

50 Ohm

Impedance

50 Ohm VSWR less than 2:1

Range

10 MHz - 3 GHz

Sensitivity

< 0.8 mV at 100 MHz
< 6 mV at 300 MHz
< 7 mV at 1.0 GHz
< 100 mV at 2.4 GHz

Max. input

15 dBm


Photo


 

btn_co_j